共查询到20条相似文献,搜索用时 93 毫秒
1.
在我国,缺陷产品安全问题已经引起政府和民众的高度重视,完善缺陷产品召回制度的呼声与日俱增。文章从缺陷产品召回的法律依据分析人手,剖析了我国缺陷产品召回制度的现状,指出分级式监管模式是未来发展的方向;探讨了缺陷产品召回分级监管模式,给出了信息收集与研判、缺陷调查与认定、缺陷产品召回3个关键性流程;分析了缺陷产品召回分级监管模式的重点工作,着重介绍了缺陷信息管理平台建设、产品缺陷专家队伍建设和风险监测与评估3个环节。 相似文献
2.
文章从内控缺陷的严重性、产生的根源和内控缺陷性质三个不同的角度,分析上市公司内控重大缺陷。根据内控缺陷划分标准,采集2010年上市公司的样本,建立内控缺陷数据库,基于内控缺陷数据库制定2010年上市公司内部控制缺陷分布图。建立了主要内部控制缺陷与驱动因素的实证模型,并进行回归分析,得出了影响内控缺陷的主要驱动因素。 相似文献
3.
压力容器属于特种设备的范畴,在工业生产与日常的生活中有着较为广泛的应用,同时还有着极其具有安全隐患的特点,必须通过检验及时发现存在的缺陷.文章描述了压力容器常见缺陷的类型,及表面缺陷和埋藏缺陷.介绍了适用于表面缺陷的目视检验、磁粉检测、渗透检测,以及适用于埋藏缺陷的超声检测、射线检测等常用的检验方法. 相似文献
4.
5.
压力容器在承压状态下工作,并且所接触的介质多为高温或易燃易爆毒性物质,使用中一旦发生事故,就会危及正常生产,甚至引起火灾、中毒、爆炸等恶性事故,给人们的生命财产造成不可估量的损失。本文就压力容器一些常见缺陷的处理提出相应建议,并对缺陷处理中的注意事项进行了探讨。常见缺陷的处理在役压力容器常见的缺陷是表面缺陷和焊缝内部缺陷。表面缺陷主要有裂纹、腐蚀、变形、机械损伤、工 相似文献
6.
本文讨论了通过漏磁检测和识别管道内外壁缺陷的方法.检测器以一定的速度通过缺陷,在缺陷处产生剩余漏磁场,通过霍尔元件检测到的信号频率与幅值来判断缺陷的大小、形状、还有内外壁分布.研究结果显示漏磁信号的不同特性是管道内外壁缺陷检测与识别的一种手段,它提高了缺陷判断的完整性. 相似文献
7.
本文针对船舶轮机检验过程中常见的缺陷以及排除缺陷的相关的原则、方法进行了分析,最后得到了具体排除轮机缺陷的措施。 相似文献
8.
9.
10.
周鑫 《中国高新技术企业评价》2013,(31):29-30
文章介绍了5052合金带材表面油斑缺陷产生的机理,分析了引起油斑缺陷的主要因素,系统地总结了轧制、精整和热处理等工序防控铝板带材油斑缺陷的措施。 相似文献
11.
本文通过对船舶轮机检验概述、船舶轮机缺陷引起的安全事故举例以及船舶轮机常见缺陷总结进行了分析,得到了针对轮机常见缺陷的具体应对措施。 相似文献
12.
近年来不论是铁路隧道还是公路隧道,由隧道二衬缺陷导致的安全质量事故频发,隧道缺陷的排查整治成为交通行业的一股暗流.本文通过对隧道缺陷调研分析,分析出引起隧道二衬缺陷的各种末端因素,通过各种新技术、新工艺、新设备的应用,从隧道二衬施工源头对引起隧道二衬缺陷的末端因素进行防控,减少或避免隧道二衬出现的概率,从而保障后期隧道... 相似文献
13.
Investigations on acceptance sampling have attached rather few importance to defects inspection. For modern quality control,
both the steadily increasing complexity of products and the need for differentiated cost calculation involve a clear demand
for economic defects sampling in its practically most relevant form: lot-by-lot single sampling plans, where the OC (lot OC)
is considered as a function of lot sizeN, sample sizen, acceptance numberc, number of defects in the lotK. Starting from an appropriate lot OC function, the present paper develops an economic cost and control model and an economic
objective function for single defects sampling plans by adapting theα-optimal sampling scheme, introduced by E. von Collani for defectives inspection, to the purposes of defects inspection. A
simple and accurate approximation ofα-optimal defects plans is derived by means of a Poisson approximation of the lot OC function. 相似文献
14.
文章主要对钢结构工程在制作、螺栓连接、拼装以及吊装工程中常见的一些质量通病及其产生的原因详细进行介绍,并对质量通病提出相应的预防措施。 相似文献
15.
本文着重讲述循环流化床锅炉受热面安装时留存的缺陷对锅炉运行后所造成的不必要损害,并举出部分实例,以及分析留存缺陷造成受热面损害的原因。 相似文献
16.
17.
Investigations on acceptance sampling have attached rather few attention to defects inspection. As to sampling models and
the corresponding operating characteristic (OC) function of single defects sampling plans, generally only typeB (process model) has been considered: sampling from a production process where the OC is conceived as a function of sample
sizen, acceptance numberc, and process average number of defects per itemλ. For modern quality control, both the steadily increasing complexity of products and the need for differentiated cost calculation
involve a clear demand for defects sampling in its practically most relevant form: lot-by-lot single sampling plans, where
the OC (typeA, lot OC) is considered as a function of lot sizeN, sample sizen, acceptance numberc, number of defects in the lotK. The present paper develops two lot OC functions from suitable assumptions on the arrangements of the total numberK of defects over theN elements of the lot. Limiting theorems on these OC functions are used to justify to some extent the customary assumption
that the Poisson process OC can serve as an approximation for typeA. The dependence of the OC functions on sample sizen, acceptance numberc, total number of defects in the lotK is described by simple formulae. 相似文献
18.
微机保护测控装置二次缺陷常常造成严重危害,必需重点解决此类问题。文章分析了造成此缺陷的因素,并针对具体的缺陷进行理论分析然后提出了解决措施。 相似文献
19.
针对桥梁在施工过程中或使用过程中经常出现的砼蜂窝麻面、裂缝等缺陷现象,以益阳市新市渡大桥为例说明了采用灌浆法进行砼缺陷修复的处理方法。 相似文献