首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献,搜索用时 62 毫秒
1.
实验研究了一种高碳 Cr Mo V合金抗磨铸铁 ,探讨了热处理工艺和变质处理对其组织及性能的影响。结果表明 ,该材料具有较高的硬度和良好的冲击韧性 ,耐磨性优于Km TBCr15Mo3合金抗磨铸铁。  相似文献   

2.
在42CrMo钢的基础上,通过添加一定量的铌(Nb),进行微量合金化处理。在不同的铌含量下,对试样进行金相观察,比较其力学性能。材料的硬度、抗拉强度、屈服强度、断后伸长率及冲击韧性均随着含铌量的增加呈现先增加后降低的变化趋势。当材料铌含量在0.03%~0.05%时,能够达到良好的性能和组织匹配。  相似文献   

3.
对1Cr13钢进行了不同时间(5,10,20,40min)的喷丸处理,研究了喷丸处理对1Cr13钢在800℃空气中的抗高温氧化性能。高温氧化实验及表面形貌观察分析发现,喷丸处理形成了一个晶粒细化层,降低了1Cr13钢发生选择氧化所需的临界含量,氧化增重显著降低,氧化膜剥落也有所改善。喷丸处理促进了1Cr13钢表面形成选择性的保护氧化膜,提高了1Cr13钢的抗高温氧化性能,喷丸处理10~20min的试样抗高温氧化性能最佳。  相似文献   

4.
项戈丰 《化工管理》2023,(17):57-60
采用光学显微镜、扫描电镜、X射线衍射等分析手段对Mg-1.5Zn-1.0Gd-0.6Mn合金的铸态、固溶态和挤压态合金的显微组织、力学性能、体外降解性能进行了全面的研究。显微组织观察表明,Mg-1.5Zn-1.0Gd-0.6Mn合金主要由基体α-Mg相和α-Mn相以及ω相(Mg3Zn3Gd2)组成。热挤压显著细化了铸态和固溶态合金的晶粒,消除了缺陷,从而提高了合金的力学性能和耐蚀性能。该合金经过挤压后抗拉强度和屈服强度分别达到313 MPa和275 MPa,塑性也大大提高,达到了16.2%。体外浸泡试验和在SBF中的电化学测试结果表明,随着降解时间的延长,合金表面会有一层腐蚀产物生成,其主要由氢氧化镁和羟基磷灰石组成,且挤压后的耐蚀性最好,腐蚀速率最低为0.32 mm/a。  相似文献   

5.
本文就 Si、Mn、Cu 等合金元素对合金白口铸铁的显微组织、力学性能及耐磨性等方面的影响作用进行了试验研究,所得结果为正确的合金设计提供了有益的参考。  相似文献   

6.
本文研究了合金元素对铸遗热锻模具钢的热处理,组织和性能的影响。提出了铸造模具钢强韧化的途径。所研制新钢种 ZG25Cr4M。2WVSi,其700℃热强度和200~300℃冲击韧性均远优于H13。  相似文献   

7.
本文利用正交试验研究了淬火温度、回火温度、回火时间和回火次数等因素对 Cr12钢强韧性的影响。结果表明,Cr12钢采用1000~1030℃淬火,440℃两次中温回火,可显著提高Cr12钢的强韧性。此外,采用980℃淬火,280℃两次回火,其强韧性也很好。对于 Cr12型的钢的强韧化已有不少研究,如循环相变,四步热处理等,但对于某些产品,这些方法显得过于复杂。我们基于工厂的实际情况,对 Cr12钢的强韧化进行研究,选出适合该厂条件(产品:小轧辊,硬度要求在 HRC58以上,工作中受冲击载荷)的简便的强韧化方法。  相似文献   

8.
钢的淬火工艺是提高其机械性能的有效方法之一,实践证明淬火硬度影响因素中,既有单因素的影响,也有多因素交互作用的影响,利用回归旋转组合设计法对45钢进行试验,分析淬火硬度的变化规律,可以确定出最佳的淬火工艺。 一、试验方法及试验结果 试验材料:25的45钢,其成分及原始硬度见表1  相似文献   

9.
为了避免发生寒冷地区沥青面层与超高性能混凝土(UHPC)层结合不良导致的沥青面层滑移或脱落现象,对钢桥面UHPC铺装层层间剪切性能进行研究。考察涂布环氧树脂防水粘结层的成型试件分别在不同涂布厚度、不同温度、不同浸泡溶液条件下,经冻融循环后的抗剪强度变化规律,并依托实际工程对层间剪切强度进行数值模拟分析。结果表明:环氧树脂防水粘结层的最佳涂布量为0.4 kg/m2;其抗剪强度随着温度的增大而减小,在60 ℃时抗剪强度能达到1.8 MPa,高温性能良好;盐溶液环境下的冻融循环对强度的损伤大于清水环境下的损伤;数值模拟得到最不利位置剪切应力峰值远小于试验得到的环氧树脂防水粘结层抗剪强度,环氧树脂防水粘结层性能优异。研究得到的UHPC铺装层层间剪切强度规律可为延长钢桥面使用寿命提供理论依据。  相似文献   

10.
在对钢铁试样进行光谱分析时,不同钢种需要采用不同的曲线进行分析。有时,高Cr钢对Sb、Bi、Pb、N、As等元素有要求,这时就需要采用高Cr、Ni曲线对试样进行分析。经过对同一试样采用两条不同曲线测试的数据进行对比分析,证明高Cr钢可以利用高Cr、Ni不锈钢曲线进行分析。  相似文献   

11.
This paper develops a theoretical model that explains the impact of the fit between top executive characteristics and strategic orientation on organizational performance. Using the Miles and Snow typology as an integrative framework, the central propositions of the model were evaluated. The results of the empirical examination provided significant support for the administrative dimension, an aspect of the typology that has been largely overlooked thus far. Further, it was found that firms achieving a greater degree of alignment between their strategy and the profiles of top managers, generally realized superior performance outcomes.  相似文献   

12.
While most prior research suggests that the average change in market value of acquiring firms varies closely around zero, recent research grounded in the resource‐based view and organizational learning theory identify positive returns to acquirers. We contribute to this literature by focusing on acquisitions of Internet firms and the potential for the transfer of scarce resources. We hypothesize that acquisitions made by offline firms of Internet firms and by Internet firms of other Internet firms lead to positive market valuation for the acquirer. Results of an event study of 798 acquisitions of Internet firms provided support for these predictions. We also find that prior alliances with online firms do not reduce the gains from such acquisitions to offline firms. Copyright © 2006 John Wiley & Sons, Ltd.  相似文献   

13.
企业非市场与市场资源、策略及其绩效的整合互动   总被引:1,自引:0,他引:1  
企业经营战略必须同时关注非市场环境和市场环境,它应该是由非市场和市场两部分组成的。因此,本文构建了企业非市场与市场资源、策略及其绩效的整合互动理论模型以及相关研究假设,并利用问卷调查获得的数据,进行了深入地实证分析。其研究结果表明,企业非市场与市场资源、策略及其绩效之间分别都存在一种正的相关关系,而非市场与市场资源、非市场与市场策略及其非市场与市场绩效之间进一步融合能够对企业发展产生有效的整合效果,虽然非市场资源不能通过市场活动间接影响非市场绩效水平,但还是一定程度验证了市场资源、非市场策略和市场绩效之间的互动效果。  相似文献   

14.
油、套管API圆螺纹上扣后齿顶与齿底间存在间隙,各项螺纹参数的公差会影响间隙的大小,经过计算得出锥度的影响程度最大。齿顶与齿底配合间隙面积越大,油、套管API圆螺纹接头密封性越差。提高油、套管API圆螺纹接头密封性,可以采取科学控制螺纹参数、合理控制上扣扭矩和圈数、使用高密封性螺纹脂以及给螺纹镀层等方法。因此,建议对密封性要求较高的油气井使用特殊螺纹接头。  相似文献   

15.
We revisit the questions of identification of outlying firms within industries and their impact on the relative importance of firm‐ and industry‐specific factors for firm performance. In response to McNamara, Aime and Valler (2005), we argue that the key results in Hawawini, Subramnian and Verdin (2003) are insensitive to the varying methods used to identify firm outliers. Further, we argue that conducting tests on industry outliers are inconsistent to what is indicated by theory and past empirical results on the relative importance of firm and industry effects to firm performance. Firm effects may matter most for outperforming and underpeforming firms, while industry effects may be at least as important to firms ‘stuck in the middle’. Copyright © 2005 John Wiley & Sons, Ltd.  相似文献   

16.
金融危机使企业并购活动受到一定负面影响,但总体趋势良好。网络型产业在国民经济中的作用逐步凸显,相关研究受到广泛关注。在对网络型产业概念界定的基础上,沿用哈佛学派的SCP分析范式构建网络型产业并购绩效评价体系,并对影响其绩效的因素进行分析。最后,从四个维度对进一步研究提出展望。  相似文献   

17.
油气勘探开发投资绩效评价的指标选择   总被引:2,自引:0,他引:2  
提出了一个如何评价油气勘探开发投资绩效的问题,并根据油气勘探、开发投资的特性及投资绩效评价指标的选择原则,并辅以单位勘探成本、单位开发成本两个指标进行比较和分析,阐明了采用单位勘探开发成本作为主要评价指标以替代目前油田企业沿用多年的旧指标的依据。  相似文献   

18.
醇基涂料可以满足铸造性能要求而得到广泛应用,将复合悬浮剂和新型纳米分散剂加入到醇基涂料中是近年来的研究热点。介绍了醇基涂料的工艺性能以及工作性能方面的研究现状,指出了提高醇基涂料悬浮性和透气性的具体方法:采用加入更有效的悬浮剂和控制制备工艺两种方法来提高醇基涂料的悬浮性;涂料透气性的影响因素主要有耐火骨料的形状和粒度,在铸造浇注的恶劣条件下,耐火骨料的变化以及黏结剂的分解使得涂料的高温透气性不同于低温透气性,将有机黏结剂与无机黏结剂混合使用是醇基涂料黏结剂的发展趋势,加入纤维状耐火骨料提高涂料强度是今后的重要研究方向。  相似文献   

19.
We analyze performance and emotions as antecedents and consequences of team strategic decisions to explore a new routine versus exploiting an existing one. In a laboratory study, we examine team decision making over time and draw causal inferences about the relationships among team emotions, team performance, and explore–exploit decisions. We use self‐report data to measure team emotions, and validate results with psychophysiological data. We find that declines in performance increase the likelihood that teams decide to explore new routines rather than exploit existing ones. We also find a marginal positive effect of positive emotions, as measured by both self‐report and psychophysiological data, on team decisions to explore a new routine. Further, teams successful at implementing new routines report increased positive emotions, as measured by the self‐report data. This relationship is fully mediated by performance change. Copyright © 2015 John Wiley & Sons, Ltd.  相似文献   

20.
The present paper examines the issue of whether interpersonal relationships are critical for global marketing of industrial products. The fields of relationship marketing, IMP group research, sales research, and network theory have stressed the importance of interpersonal relationships in the business-to-business or industrial marketing context. In contrast to this emphasis on interpersonal relationships, we argue that industrial firms can both conceive and enhance marketing strategies based on developing high quality and consistent processes, products, services or outcomes (consistent processes and outcomes). Such strategies are especially important given the fact that developing interpersonal relationships is expensive due to their reliance on frequent and/or face-to-face communications. In this paper, we examine industry and country contexts that lead to the choice of alternative industrial product marketing strategies and highlight some future research directions and managerial implications.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号